Sync 1 Rear View Camera under Sync 3

Auto configuration discussions and feel sharing

beatsteak
Posts: 6
Joined: Mon May 17, 2021 1:03 pm
Vehicle: Ford Focus DYB, 2.0tdci Powershift 140>190PS, 2013

Sync 1 Rear View Photographic camera under Sync 3

Hey,

i inverse Sync i to Sync 3, i have original RVC build in, just with Sync iii it`s not working. I plugged a Fakra to Cinch Adapter betwixt Camera and the new Upgrade harness (it has Cinch for RVC).
At present i`thousand non sure where i have to cahnge de AsBuilt that the Camera will be recognized by Sync 3.
I employ Forscan and (sometimes focccus) with EM327 (HS/MS Can)

beatsteak
Posts: 6
Joined: Mon May 17, 2021 1:03 pm
Vehicle: Ford Focus DYB, 2.0tdci Powershift 140>190PS, 2013

Re: Sync 1 Rear View Camera under Sync 3

Mail service by beatsteak »

I set it to "B" (Because Photographic camera and Rear Sensors) only it was not functional.
In that location are a lot of Options like AUX Photographic camera and and then on in the APIM Configuration.
Volition try some changes with Focccus, needed the correct VBF File showtime.

this site is same database than cynlab, merely with working "search" :-)
https://naviupgrade.com/asbuilt-programming-database/

In this threat is also the same Dapter used for camera plugin and only some cahnges in Focccus at the end
https://www.fordownersclub.com/forums/t ... 14-models/

123 – Audio Aux Input = 01 (without)
125 – DAB Radio System = 01 (without)
154 – Module USB = 01 (without)
157 – bluetooth Handsfree = 01 (without)
172 – Front Display = 09 (DM8 with nav)
214 – ICP = 09 (unknown)

Ghano38
Posts: 580
Joined: Sat Dec 07, 2019 nine:10 am
Vehicle: Ford c max

Re: Sync 1 Rear View Camera under Sync iii

Postal service by Ghano38 »

Forget about Focccus since you lot upgraded to Sync 3,if you accept OEM photographic camera y'all merely accept to connect video + and video - to pin 14 and xv respectively of the Sync 3 apim connector with the appropriate adapter cable than with Forscan go to apim main configuration and check out if the rear camera is activated or non.

beatsteak
Posts: 6
Joined: Monday May 17, 2021 1:03 pm
Vehicle: Ford Focus DYB, 2.0tdci Powershift 140>190PS, 2013

Re: Sync one Rear View Photographic camera under Sync 3

Post past beatsteak »

Ist is connected throug Fakra>Sure-fire Adapter and enabled in APIM Configuration.
But Sync says that the photographic camera is not bachelor.
Is there any signal i tin read out with Multimeter to check the camera Signal?
Tomorrow i will check If the chinch out of harness is continued to the correct pins.
But i am sure they built ist right.

Focccus Connexion is not possible, fifty-fifty if i have the correct vbf now :?

consp
Posts: 108
Joined: Sat May 19, 2018 11:xvi am
Vehicle: Fiesta 125hp 2017 (My13.25 Mk7.5, With EU Sync3)

Re: Sync ane Rear View Camera under Sync iii

Mail service by consp »

Always good to encounter a commercial party stealing someones'south work without attribution.

Is in that location any signal i tin read out with Multimeter to check the camera Signal?

It's an NTSC Video signal, so you'd need a proficient multimeter or a portable oscilloscope or a portable monitor with video in. Maybe yous can observe some signal. If I recall correctly invalid signals volition testify black, asunder bluish screens. (or the other mode around). Eventually it will stop displaying the RVC screen and switch to PDC only.

The configuration of the APIM is independent of the Primal configuration. If y'all enable the RVC and put it in opposite the APIM should brandish what information technology gets (image/black/blue screen).

Usually no image = reversed polarity.

You can test the cable if you tin disconnect it at the rear end and measure for continuity if you recollect it is broken. It's unremarkably a 6 pin connector with pins 3&4 for the signal with pin 4 existence the + if I recollect correctly:

Image

smartguy69
Posts: 217
Joined: Monday Sep 21, 2020 8:27 pm
Vehicle: Kuga Titanium,2 litre diesel, 150PS, 2015

Re: Sync ane Rear View Camera under Sync 3

Post by smartguy69 »

beatsteak wrote: ↑

Wed May 19, 2021 12:33 pm

Hey,

i changed Sync 1 to Sync 3, i have original RVC build in, simply with Sync iii it`s non working. I plugged a Fakra to Cinch Adapter betwixt Photographic camera and the new Upgrade harness (it has Sure-fire for RVC).
At present i`m non sure where i take to cahnge de AsBuilt that the Photographic camera volition exist recognized by Sync 3.
I utilize Forscan and (sometimes focccus) with EM327 (HS/MS Can)

On the sync 1 display (4.2" screen) with the 12 pin plug, where did you connect pins 6 and 12 to.

beatsteak
Posts: half dozen
Joined: Mon May 17, 2021 1:03 pm
Vehicle: Ford Focus DYB, 2.0tdci Powershift 140>190PS, 2013

Re: Sync 1 Rear View Photographic camera under Sync 3

Post past beatsteak »

At Weekend i've got a camera view sometimes, so i expected that the cinch>Fakra Adapter is broken and tried another one.
Simply it was not the Adapter.

So i tried today and to detect the mistake.
If i disconnect the master connector of the ACM i become photographic camera view.
I found a red ignition cable, ( double ) that was out of its connector. Don't know where Information technology has to bei plugged in.
Tomorrow i volition attempt to disconnect one Pin after another, promise i will find the error.

Any idea which pin of the ACM could exist the broken?

MaoVi
Posts: one
Joined: Dominicus Dec xxx, 2018 8:25 pm
Vehicle: Ford Kuga MK2 2.0 TDCI 180PS DW10F SPORT X 2014

Re: Sync 1 Rear View Camera nether Sync 3

Postal service by MaoVi »

Hello,
Did you find the issue? I have the same situation like you lot after retrofitting to sync3, my mill sync1 photographic camera not prove any video. Thank you for any entry